Lighting, Lighting

Lighting includes use of both artificial light sources such as lamps and natural illumination of interiors from daylight. Daylighting (through windows, skylights, etc.) is often used as the main source of light during daytime in buildings given its low cost. Artificial lighting represents a major component of energy consumption, accounting for a significant part of all energy consumed worldwide. Artificial lighting is most commonly provided today by electric lights, but gas lighting, candles, or oil lamps were used in the past, and still are used in certain situations. Proper lighting can enhance task performance or aesthetics, while there can be energy wastage and adverse health effects of lighting. Indoor lighting is a form of fixture or furnishing, and a key part of interior design.

A fixture using replaceable light sources can also have it's efficiency quoted as the percentage of light passed from the "bulb" to the surroundings. The more transparent the lighting fixture is, the higher efficacy. Shading the light will normally decrease efficacy but increase the directionality and the visual comfort probability.

This is often done with fluorescent lighting or rope light, or occasionally with neon lighting.

It has regained some popularity recently in low-voltage tracks, which often look nothing like their predecessors because they do not have the safety issues that line-voltage systems have, and are therefore less bulky and more ornamental in themselves. A master transformer feeds all of the fixtures on the track or rod with 12 or 24 volts, instead of each light fixture having its own line-to-low voltage transformer. There are traditional spots and floods, as well as other small hanging fixtures. A modified version of this is cable lighting, where lights are hung from or clipped to bare metal cables under tension.

A torchiere is an uplight intended for ambient lighting. It is typically a floor lamp but may be wall-mounted like a sconce.

The standard lamp and shade that sits on a table is general lighting, while the desk lamp is considered task lighting. Magnifier lamps are also task lighting.

This uses diffuser panels hung like a suspended ceiling below fluorescent lights, and is considered general lighting. Other forms include neon, which is not usually intended to illuminate anything else, but to actually be an artwork in itself. This would probably fall under accent lighting, though in a dark nightclub it could be considered general lighting. Underwater accent lighting is also used for koi ponds, fountains, swimming pools and the like.

In the 2000s, neon lighting is increasingly yielding to digital vehicle lighting, in which bright LED are placed on the car and operated by a computer which can be customized and programmed to display a range of changing patterns and colors, a technology borrowed from Christmas lights.

Specialists who work with lighting, carefully avoid energetic units for measuring of the light output of sources of light due to the spectral response of human visual perception. For example, instead of watt per steradian, the special unit candela is used; 1 candela=(1/683) W/steradian for monochromatic light at 555 nm wavelength. Common characteristics used to evaluate lamp quality include efficiency measured in lumen per watt, typical lamp life measured in hours, and Color Rendering Index on a scale of 0 to 100. Cost of replacement lamps is also an important factor in any design.

Comprehensive lighting design requires consideration of the amount of functional light provided, the energy consumed, as well as the aesthetic impact supplied by the lighting system. Some buildings, like surgical centers and sports facilities, are primarily concerned with providing the appropriate amount of light for the associated task. Some buildings, like warehouses and office buildings, are primarily concerned with saving money through the energy efficiency of the lighting system. Other buildings, like casinos and theatres, are primarily concerned with enhancing the appearance and emotional impact of architecture through lighting systems. Therefore, it is important that the sciences of light production and luminaire photometrics are balanced with the artistic application of light as a medium in our built environment. These electrical lighting systems should also consider the impacts of, and ideally be integrated with, daylighting systems. Factors involved in lighting design are essentially the same as those discussed above in energy conservation analysis.

Based on the positions and mounting heights of the fixtures, and their photometric characteristics, the proposed lighting layout can be checked for uniformity and quantity of illumination. For larger projects or those with irregular floor plans, lighting design software can be used. Each fixture has its location entered, and the reflectance of walls, ceiling, and floors can be entered. The computer program will then produce a set of contour charts overlaid on the project floor plan, showing the light level to be expected at the working height. More advanced programs can include the effect of light from windows or skylights, allowing further optimization of the operating cost of the lighting installation.

Where multiple lamps are used to illuminate the same area, each one's contribution is summed. Again the tabulated light levels (in lux or foot-candles) can be presented as contour lines of constant lighting value, overlaid on the project plan drawing. Hand calculations might only be required at a few points, but computer calculations allow a better estimate of the uniformity and lighting level.

Clearly, much less light is required to illuminate a hallway or bathroom compared to that needed for a word processing work station. Prior to 1970 (and too often even today), a lighting engineer would simply apply the same level of illumination design to all parts of the building without considering usage. Generally speaking, the energy expended is proportional to the design illumination level. For example, a lighting level of 80 footcandles might be chosen for a work environment involving meeting rooms and conferences, whereas a level of 40 footcandles could be selected for building hallways. If the hallway standard simply emulates the conference room needs, then twice the amount of energy will be consumed as is needed for hallways. Unfortunately, most of the lighting standards even today have been specified by industrial groups who manufacture and sell lighting, so that a historical commercial bias exists in designing most building lighting, especially for office and industrial settings. Beyond the energy factors being considered, it is important not to over-design illumination, lest adverse health effects such as headache frequency, stress, and increased blood pressure be induced by the higher lighting levels.

Not only will greater reliance on natural light reduce energy consumption, but will favorably impact human health and performance. For example, it is clear that student test scores are improved for children who learn in the presence of greater natural light. Artificial night-lighting has been associated with irregular menstrual cycles.

This certification process is one of three national (U.S.) examinations (the others are CLEP and CLMC) in the lighting industry and is open not only to designers, but to lighting equipment manufacturers, electric utility employees, etc. Generally speaking there is no legal or practical requirement for the lighting design team to possess the certifications discussed.

Its members include manufacturers and distributors of stage and entertainment lighting, sound, rigging and similar products and services, and affiliated professionals in the area. They lobby for and represent the interests of the industry at various levels, interacting with government and regulating bodies and presenting the case for the entertainment industry. Example subjects of this representation include the ongoing review of radio frequencies (which may or may not affect the radio bands in which wireless microphones and other devices use) and engaging with the issues surrounding the introduction of the RoHS (Reduction of Hazardous Substances) regulations.

ISLE promotes lighting education, helps research and exchange of information and knowledge among the professionals.

Source: Wikipedia > Lighting